After rejecting two batches of electric linear actuators in 2024 — roughly $34,000 in rework and a three-week line delay — I stopped treating datasheets as sourcing documents. The specifications procurement usually compares (rated force, stroke, speed, voltage) match across dozens of suppliers on paper. What separates an actuator that runs 200,000 cycles from one that seizes at 40,000 rarely appears on the spec sheet at all. Three numbers do predict reliability, and most suppliers won't volunteer them unless you know to ask.
Ask anyway. Here's what I mean, and why — in my experience — the questions on this list have saved us more than any per-unit price negotiation.
The three questions that matter more than the datasheet
1. What is the spec tolerance, not just the spec?
A "12V actuator rated at 1,500N" tells you almost nothing until you know the ±. Is rated force ±5%, ±10%, ±20%? Same question for stroke length and stroke position accuracy.
We got a batch last year where the stroke came in at 203mm against a 200mm spec. The vendor's response: "within industry standard." They were right — ±2% is generous but common. It was still 3mm off our assembly jig, which was built for ±1mm. They redid it at their cost, but we lost nine days. The tolerance was never printed on the datasheet. It was the first thing the next contract required.
If a supplier can't give you a number instead of "industry standard," treat that as a number too.
2. What was tested duty cycle, at what ambient temperature?
"Intermittent duty" is a meaningless phrase. It's a category, not a measurement. What you need to know is: at what duty cycle was the endurance tested (20%? 50%?), for how many continuous hours, and at what ambient temperature?
Datasheets usually list a duty cycle rating. What they don't list is whether that rating was measured at 25°C or 40°C. The same unit rated for 25% duty at 25°C may derate by roughly half at 50°C ambient. If your application sits inside a cabinet or runs outdoors in summer, that distinction is the whole ballgame.
I want to say one supplier quoted 30% continuous duty for a heavy-duty unit we were screening (this was Q2 2024, pricing around $220 per unit at 1,000 MOQ) — and when I asked for test conditions, the answer was "standard lab," which turned out to mean 22°C with a fan on the motor. Don't quote me on the exact ambient, but you get the point. It was close to a 40% derate in our enclosure.
3. Show me test data from three consecutive production batches.
Prototypes pass. That's what they're for. Production consistency is where new relationships actually break. Ask for force output, current draw, and speed at rated load — pulled from three consecutive production lots, not the development unit.
If the supplier can produce that data, you're probably talking to a manufacturer. If they can't, that tells you something too.
Why the spec sheet misleads even when it's honest
From the outside, the spec sheet looks like the objective basis for a sourcing decision. The reality is it describes the motor under ideal conditions and tells you little about how a specific unit behaves in your machine.
Three examples I've run into repeatedly:
- High speed and heavy duty fight each other. In a given package size, speed and force trade off through the gear ratio. A supplier claiming both a 12V high-speed actuator and heavy-duty load capacity is asking you to believe the physics works out. Usually one is derated. Ask which. (Sometimes it's neither — but they only publish the high-speed number.)
- 12V voltage drop. Datasheet specs assume the motor terminal sees 12.0V. On a 2–3m cable run at 10A, you're losing meaningful voltage before the motor ever sees it — enough to cut force output by 10% or more. That number isn't in the brochure (it depends on your cable, not their motor).
- IP ratings without cycling. IP65 means dust-tight and protected against water jets per IEC 60529. But that rating can be granted without cycling the actuator under load for thousands of strokes. Seals wear at the moving interface, not at rest. Ask whether the IP rating was tested on a static unit or a cycling one.
The sourcing-layer problem
It's tempting to think "electric linear actuator manufacturers" means every site that uses that phrase is a factory. But a meaningful share of the websites that rank for that term are trading companies front-ending a factory somewhere. A trading company can quote you a price. It struggles to tell you whether the endurance test ran at 25°C or 40°C, because it wasn't in the room.
The "always source direct" advice ignores the reality that some trading companies run better incoming inspection than the factory does. But at minimum, before the first production order, ask for the factory address (not a PO box) and a video walkthrough of the assembly line. A manufacturer will usually send one inside a day. A trading company asks why you want it.
What I got wrong, and what it cost
I assumed identical specifications meant identical performance across vendors. Didn't verify. Turned out every supplier had a slightly different interpretation of "operating temperature" — some rated at -10°C to 60°C, some at 0°C to 40°C, and none of them printed the range near the force spec where I was looking.
We shipped a batch of actuators inside a cold-storage door application. The units met every number on the datasheet. The grease inside didn't — it thickened below 5°C and the drive stalled on maybe 15% of units inside the first winter. The defect ruined roughly 8,000 downstream assembly hours and put our brand on a customer complaint about equipment that "met spec."
Now every purchase contract includes an operating temperature requirement with a test method attached. That's the trade we make: the actuator we ship carries our name, not the supplier's. A unit that fails in the field costs us maybe 10x what the component did — and the client remembers the brand on the cabinet, not the motor inside it.
When this advice doesn't apply
If you're prototyping, ordering under 100 units a year, or running a light duty cycle (a few hundred strokes per year), the datasheet is probably enough. The due diligence I'm describing — test data requests, factory walkthroughs, tolerance negotiations — costs real time on both sides. It's not free, and it's not always worth it.
It also doesn't apply if you already have a supplier with a decade of clean runs behind them. Don't break a working relationship to run a question audit. The value of an established supplier is that they've already paid for the mistakes you're trying to avoid.
Where it does apply: new relationships, high duty cycles, cold or hot environments, and anything customers will see in the field under your brand name. In those cases, the three questions above are the cheapest insurance you can buy — cheaper than the $34,000 lesson, at least. That one I know exactly, because I paid it.